Sound Advice | Cable management
Today's LessonCable management is a great way to increase the aesthetic appeal of your stage setup as well as promote a bit more safety around your gear. There are a couple widely accepted methods for...
View ArticleHow To | Use the TouchMix User Buttons to get to ALL (8) DCA faders.
ProcedureGo to MenuGo to User ButtonsUnder Action Column Touch-Go to ScreenUnder Selection Column-Touch OtherUnder Detail Column Touch DCA FadersAssign User Button to any User Button 1-8Touch Assign...
View ArticleFAQ | Why do my recordings sounds like they are out of sync or slowed...
AnswerThis is usually due to the initial recording being done on a hard drive that is under performing and can not keep up with recording from the Touchmix. We always recommend using a Solid State Hard...
View ArticleSound Advice | Mixing monitors using a wireless tablet
Today's LessonWhether you’re the sole monitor mixer for an event or you’re managing both FOH and monitors, there are some real advantages to managing monitors with an iPad from the stage.Number one,...
View ArticleFAQ | What is the main difference between legacy K and K.2 Series?
AnswerThere are many differences:K.2 amp has over twice the Peak power of legacy K with more efficient distribution of power (1800 W for the LF + 225W for the HF).K.2 has more powerful DSP, and now...
View ArticleFAQ | What is QSC Acoustic Linear Phase (ALP) design?
AnswerQSC ALP design employs a combination of FIR, IIR and all-pass filters to address a number of phase-related shortcomings found in many loudspeakers. Used across a range of QSC loudspeakers, ALP...
View ArticleFAQ | What is the maximum Delay time you can set on the K.2 series of...
AnswerThe maximum Delay time is 100mS, which equates to approximately 112.6ft (34.6m).
View ArticleFAQ | Is the fan in the K.2 Series variable speed?
AnswerYes. Once the amplifier reaches a certain temperature, the fan engages at very a low speed, and as the amplifier heats up, a clever algorithm in the DSP will instruct the fan to speed up...
View ArticleTraining | TouchMix Series Digital Mixers
InformationQSC has several training videos available for TouchMix Series Digital Mixers. Please see the info below to get started on your product.QSC TouchMix TrainingTouchMix Training 01: Mixer...
View ArticleFAQ | What is the Patch Matrix on TouchMix Series Mixers?
AnswerThe patch matrix allows a physical, analog input to be routed to a channel other than the one it is assigned to by default. This may be useful to rearrange the mixer’s layout. Let’s say you’ve...
View ArticleFAQ | Do I need two KS118 subwoofers for the cardioid configuration to work?
AnswerYes, this configuration requires at least two KS118 subwoofers.
View ArticleFAQ | Can the K, KW, KS, and K.2 power cables work interchangeably?
AnswerYes, the power cables for the K, KW, KS, and K.2 use the same Volex connector, as well as the same AWG. This means that they can be used with any unit. The lengths may vary.
View ArticleFAQ | What is the crossover frequency between the subs and the tops?
AnswerAll of the K and KW loudspeakers will accept a full range signal. If you are using the KSub or KW181 there is a low pass filter set in the DSP at 100Hz. When the Ext. Sub switch on a K or KW top...
View ArticleFAQ | Can K.2 Series loudspeakers be used in a cluster or line array?
AnswerNo. While K.2 Series loudspeakers can be permanently installed, their design and mounting hardware is not intended for cluster or line array applications. If the intended use case requires a...
View ArticleSound Advice | Controlling stage volume - Mic the guitar amps
Today's LessonKeeping the overall stage volume down is very helpful when controlling your monitor volume. One thing we can do here is to keep any guitar cabinets on stage at low volume. The cabinet...
View ArticleFAQ | Are the E Series loudspeakers IP rated?
AnswerThe E Series loudspeakers are intended for use in portable/mobile systems and controlled environment installs (I.E. bars, clubs..etc). While these do have treated speakers, the enclosures are not...
View ArticleFAQ | Can you use the TouchMix Antifeedback wizard on both the FOH and...
AnswerYes. Separate Anti-Feedback Wizards are available on the Main and Aux Outputs. Press the top of the output to open the Overview Screen, then press the Anti-Feedback tab to access settings for the...
View ArticleSound Advice | Calculating power consumption of your gear
Today's LessonBefore you start plugging things in at a venue, it’s good to know how much power you gear needs so you can use the available power appropriately and avoid overloading circuits when you...
View ArticleFAQ | What is the range of the wi-fi dongle included with the TouchMix mixer?
AnswerApproximately 50 to 75 ft (15 to 22 m), dependent on direct line of sight.
View ArticleHow To | Use the TouchMix User Buttons to get to the output notch Filter/Anti...
ProcedureGo to MenuGo to User ButtonsUnder Action Column Touch-Go to ScreenUnder Selection Column-Touch Output FiltersUnder Detail Column Touch Main (L/R) or Any Aux 1-14Assign User Button to any User...
View Article