FAQ | How many K.2 speakers can be connected to a single circuit?
AnswerThe K.2 Series models feature a 2000-watt class D module with that are very efficient at AC draw or consumption. That means you can run multiple K.2 loudspeakers off a single 15 or 20-amp AC...
View ArticleFAQ | What type of Speaker Pole Cup is on the KS212C Cardioid Sub?
AnswerThe KS212C Cardioid Sub actually features two M20 threaded Pole Cups – one on the top (for vertical orientation of the sub) and one on the side (for horizontal orientation of the sub). There is...
View ArticleFAQ | Is the KS118 flyable?
AnswerThe KS118 does not have hardware intended for flying. For a flyable sub, please see the KLA181 or passive GP118-sw.
View ArticleFAQ | What is DEEP™ mode on the KS118 subwoofer?
AnswerDEEP™ mode is a proprietary algorithm that offers additional low frequency extension and output (optimal for bass-heavy electronic and dance music), but at the expense of sensitivity when engaged...
View ArticleFAQ | Can I power an additional passive loudspeaker off my K.2/KW/KLA/CP...
AnswerThe question often comes up among users of K.2, KW, KLA, and CP Series active loudspeakers: How can I run a passive loudspeaker off my active loudspeaker?The answer is you cannot; each QSC active...
View ArticleTroubleshooting | My TouchMix-30 Pro shows ‘Unknown Device’ in the Device...
Affected ProductsHardware Model/SeriesTouchMix-30SoftwareControl App: 3.0.22Firmware: 3.0.12462ProblemTouchMix-30 Pro shows ‘Unknown Device’ in the Device List under Remote Control Settings.CausesThis...
View ArticleFAQ | Are the Q-SYS NS Series switches configured to address the IGMP...
AnswerYes, the NS Series switches are pre-configured specifically to meet the performance requirements of Q-SYS audio, video and control data, along with support for AES67 and Dante audio streams.
View ArticleFAQ | Can I use the dongle from the TouchMix 8 or TouchMix 16 with the...
AnswerYes you can. However, for professional results we strongly recommend using an external router. The ethernet port on the TouchMix-30 Pro is active and can accept a direct link to a router.
View ArticleFAQ | Do the K.2 loudspeakers go into Auto-Standby like the legacy K...
AnswerYes. The K.2’s Class D amplifier will go into auto-standby if there is no signal present for a period of three (3) minutes. As soon as signal is detected the amplifier will exit standby mode...
View ArticleHow To | Use to the "Line Out" output on a K or KW loudspeaker.
ProcedureThe Line out output on a K or KW series loudspeaker is somewhat different from the direct outputs below each input. The line output is a summed output in which the 2 channels on the speaker...
View ArticleFAQ | What is phantom power?
AnswerCondenser microphones require a polarizing voltage and power for their built in amplifiers. Sometimes provision is made to supply this voltage directly though the microphone cable. The procedure...
View ArticleFAQ | Is the K.2 Series really more powerful than the legacy K models?
AnswerYes. The K.2 Series utilizes a new amplifier system that offers nearly double the power to the LF driver than did legacy K Series, while utilizing a smaller, more appropriately sized amplifier...
View ArticleFAQ | FAQ: Are the KLA Series loudspeakers IP rated?
AnswerThe KLA Series loudspeakers are intended for installed audio systems in a climate controlled environment. They are not IP rated for permanent outdoor installations.
View ArticleFAQ | How many effects does the TouchMix have?
AnswerFour instances of the six processors (two reverbs, stereo and mono delays, pitch shifter, chorus) are available and may be used in any combination. There are four dedicated effects buses, so it's...
View ArticleFAQ | Does TouchMix record the dynamics/eq/fx?
AnswerTouchMix mixers record at the gain stage (trim pots) of the mixer. This means that it prints the direct signal from the pre-amp/line inputs of the mixer.
View ArticleHow To | Make DSP settings (presets/scenes etc.) and input gains tamper-proof...
ProcedureAn accessory Lock-out Cover (K.2-LOC) is available.
View ArticleHow To | Record/Stop the Transport with a User Button on TouchMix.
ProcedureGo to MenuGo to User ButtonsUnder Action Column Touch-RecordingUnder Selection Column-Touch TransportUnder Detail Column Touch Record/StopAssign User Button to any User Button 1-8Touch Assign...
View ArticleSound Advice | EQ Tips - Frequency masking and how to avoid it
Today's LessonA common problem that occurs in so many mixes is what’s called frequency masking. A sound person wants a heavy bass sound and boosts the bass, lows and low-mids everywhere in the mix...
View Article