Tip | Live Bands using K.2 Series Application Guide.
AdviceThe QSC K.2 Live Bands Application Guide contains a wealth of recommendations, information, and instructions in regards to specific configurations and setups for Live Bands.
View ArticleError / Status | TouchMix Error 1234 - Can't connect to IP Address
Affected ProductsHardware Model/SeriesTouchMix SeriesSoftware MessageError 1234 - Can't connect to IP address shows on TouchMix.DefinitionError 1234 will populate if there is an issue with the mixer...
View ArticleFAQ | Which subwoofer is right for my needs?
AnswerWe have just the tool to help you choose the right subwoofer by answering a few questions about your indented use. Click here for our Subwoofer Selector Tool.
View ArticleFAQ | If there is no Dante® network redundancy on the LA108/LA112, what other...
AnswerFor mission-critical events (live broadcasts, etc.) it is possible to connect both Analog and Dante signals simultaneously where Dante audio is the primary source and the analog audio is the...
View ArticleSound Advice | Compression Explained
Today's LessonCompression is a useful tool that allows us to reduce the dynamic range of an audio signal making the loud parts quieter and the quiet parts louder. Compression is essential in taming...
View ArticleFAQ | Can the rigging hardware of the LA108 connect to the LA112?
AnswerNo. The width of the LA108 does not match the width of the LA112 enclosure. Therefore, they cannot be deployed or rigged in the same array.
View ArticleFAQ | What is the green connector on my K/KW loudspeaker for?
AnswerThis is a Phoenix connector that gives you the ability to remotely control the output gain of your K/KW loudspeaker using a 10K pot (wiring diagrams are available at www.qsc.com). This is...
View ArticleFAQ | Is the K TOTE compatible with both legacy K and K.2 series?
AnswerYes. They can be used interchangeably.
View ArticleQuick Tip | Using K.2 Loudspeakers as Studio Monitors
Today's LessonLearn how to set your K.2 Series loudspeakers to be used as studio monitors with the Studio Monitor preset.Press the Enter button.Use the encoder wheel to scroll to Preset.Press...
View ArticleFAQ | Does the KS212C Cardioid Sub include Casters?
AnswerYes. Four 3.0" (76 mm) ball-bearing casters are pre-fitted to the rear.
View ArticleSound Advice | What is a graphic EQ?
Today's LessonGraphic equalizers consist of multiple graphical sliders that producers and audio engineers use for altering and controlling the frequency response of an audio system.Professional...
View ArticleSound Advice | Creating a "festival" mixing scene
Today's LessonIn a music festival scenario, there will be several bands playing and you may not always know what the set is for each band until they get up on stage. This means as the mix engineer,...
View ArticleSound Advice | How to eliminate feedback with EQ
Today's LessonEQ can be a powerful tool when it comes to eliminating feedback. Here are a few quick eq tips that can help cut down on feedback when you need them.Start by applying a low cut filter on...
View ArticleFAQ | After exporting tracks from my DAW and making them into a TouchMix...
AnswerIf any track from the DAW was exported as a stereo .wav file, TouchMix will not play the session properly. Check the export settings of your DAW, make sure it is exporting all tracks as mono .wav...
View ArticleSound Advice | How to avoid comb filtering part 1: Destructive phase...
Today's LessonLet's discuss a phenomenon called comb filtering, which can have an adverse effect on the overall sound of the PA in a room. Destructive Phase InterferenceTo begin explaining comb...
View ArticleSound Advice | Shelf EQ Filters Explained
Today's LessonA shelving filter either increases or decreases the volume level of frequencies equally below, or above, a selected frequency. When you look at the result on the display is resembles a...
View ArticleFAQ | Does the K.2 Series only go 1dB louder than its predecessor?
AnswerNo. Back in 2009 when the legacy K Series was first introduced, there was no common industry practice for determining Maximum SPL of a self-powered loudspeaker therefore the Maximum SPL was...
View ArticleFAQ | What external media can the TouchMix record to?
AnswerYou can record to an external powered HDD (7200 rpm min) or SSD (minimum write speed of 150mbps) for multi-track recording, or to a USB 3.0 memory stick for stereo recording. For more information...
View ArticleHow To | Use the TouchMix User Buttons to set the Tap Tempo when using the...
ProcedureGo to MenuGo to User ButtonsUnder Action Column Touch-Tap TempoUnder Selection Column-Touch Mono Delay, Stereo Delay L or Stereo Delay RUnder Detail Column Touch FX1-FX8Assign User Button to...
View ArticleFAQ | What is the PLD amplifier latency?
AnswerPLD amplifier input to output latency is approximately 760uS or .76 milliseconds.
View Article