FAQ | Can I use L Class models in applications where they may be exposed to...
AnswerWhen LA108/LA112 loudspeakers are used in a temporary application, where rain or exposure to moisture is a possibility, the TWS-IO (Temporary Weather Shield) is recommended, which protects the...
View ArticleTroubleshooting | K.2 Speaker Displaying Firmware 9.1.1.x
Affected ProductsHardware Model/SeriesK8.2, K10.2, K12.2 Software1.3.3, 1.3.3, 1.4.1 ProblemThe speaker displays a firmware build of 9.1.1.x prior to performing an update or immediately after...
View ArticleClik here to view.
Troubleshooting | L Class showing a black screen on the Rear User Interface...
Affected ProductsHardware Model/SeriesL Class - LA108, LA112 Active Line Array LoudspeakersSoftwareFirmware 1.1.0033ProblemIn very rare circumstances, when powering up the LA108 or LA112 loudspeakers,...
View ArticleUpdate | Q-SYS Product Information
InformationIt looks like you are searching for information related to a Q-SYS product.To get the information you need, please go to the Q-SYS Knowledge Base.
View ArticleTroubleshooting | TouchMix DAW Utility not installing/opening in MacOS
ProblemDAW Utility will not install and/or open due to security settings within the MacOSCausesThe DAW Utility .dmg file may not be recognized by the MacOS as a valid installation. The OS can issue a...
View ArticleFAQ | Will the settings of the channel high and low-cut filters effect the...
AnswerYes. These filters may be used to prevent sound (such as air-handling noise) that is above and below the range of speech from affecting the operation of the automatic microphone mixer.
View ArticleFAQ | Is the 3.5mm TRS mini-jack input on the K.2 series of loudspeakers...
AnswerIt will accept a stereo source, but will always sum this down to Mono.
View ArticleFAQ | When I use the TouchMix automatic microphone mixer, how does it change...
AnswerThe automatic microphone mixer has no effect on signal routing. Wherever you were sending your signal before you assigned a channel to the automatic microphone mixer is where it will go afterwards.
View ArticleFAQ | What is the standby amp usage for the CP Series loudspeakers?
AnswerCP Series loudspeakers draw less than 0.1 amps when in an idle state (i.e., no audio is flowing through the amp).
View ArticleHow To | Use the TouchMix User Buttons to clear all channels that have...
ProcedureGo to MenuGo to User ButtonsUnder Action Column Touch-UtilityUnder Selection Column-Touch ClearUnder Detail Column Touch ClipAssign User Button to any User Button 1-8Touch Assign ButtonAre you...
View ArticleFAQ | Where can I find the K.2 Series user manual?
AnswerYou can find the K.2 Series user manual attached to this article, or on the K.2 product pages of the QSC website.
View ArticleTraining | CP Series Powered Loudspeakers
InformationQSC has several training videos available for CP Series Powered Loudspeakers. Please see the info below to get started on your product.Tech Talk: CP Series Compact Powered Loudspeakers...
View ArticleFAQ | What is the maximum Delay time available on the KS118?
AnswerThe maximum Delay time is 100 ms, which equates to approximately 112.6 ft (34.3 m).
View ArticleHow To | Use the TouchMix User Buttons to force highlighted Fader or Knob to...
ProcedureGo to MenuGo to User ButtonsUnder Action Column Touch-UtilityUnder Selection Column-Touch Selected ParameterUnder Detail Column Touch Fader to 0 dbAssign User Button to any User Button...
View ArticleFAQ | Can I use the the TouchMix automatic microphone mixer to mix my band?
AnswerAutomatic microphone mixers are intended primarily for speech applications such as panel discussions. They are also sometimes used in theatrical sound reinforcement. Automatic microphone mixers...
View ArticleFAQ | What are the installation options for CP Series loudspeakers?
AnswerYou can use the CP yoke or the speaker pole cup for installation.NoteThe CP series does not offer rigging points to fly the speakers.
View ArticleFAQ | TouchMix-30 | My iOS device will not update to iOS17, can I still use...
AnswerYes. You can use older IOS mobile devices running an older IOS builds with the Touchmix-30 Pro Control App version 3.0.22 as long as the app is visible in the Apple Store on your device. The...
View ArticleFAQ | Are there any times when my K.2 loudspeaker will not go into Auto-Standby?
AnswerIf you have a mobile device connected to the 3.5mm Input and turned down, there may still be enough crosstalk that the loudspeaker is detecting light signal. Likewise, if you have Input B set to...
View ArticleHow To | Set up In Ear Monitors (IEM) with TouchMix mixers
ProcedureTouchMix mixers all have the capability to drive wired, stereo In Ear Monitors (IEM) directly. For performers such as keyboardists and drummers who stay at one place on stage, this is a simple...
View ArticleFAQ | Where do I find service manual to repair my product?
AnswerService manual are only available to QSC Authorized Service Partners. If you are having troubles with your equipment, Create a Case or contact QSC Technical Support for assistance.
View Article