FAQ | Is the KS118 flyable?
AnswerThe KS118 does not have hardware intended for flying. For a flyable sub, please see the KLA181 or passive GP118-sw.
View ArticleTip | Clubs and Venues using K.2 Series Loudspeakers Application Guide.
AdviceThe QSC K.2 Clubs and Venues Application Guide contains a wealth of recommendations, information, and instructions in regards to specific configurations and setups for clubs and venues.
View ArticleFAQ | The KLA12 loudspeaker had an 18° vertical coverage angle, while the...
AnswerYes. However, maximum vertical coverage is not always the most desirable attribute of a line array system. The decreased vertical coverage of the LA108/LA112 loudspeakers combined with more...
View ArticleHow To | Send a mono signal to both inputs of a GXD amplifier.
ProcedureIf you want to send a mono signal to both channels of a GXD amplifier, you need to send the mono signal into the XLR input of channel 1, then use the 1/4 inch input of channel 1 to jump the...
View ArticleTroubleshooting | My TouchMix-30 Pro shows ‘Unknown Device’ in the Device...
Affected ProductsHardware Model/SeriesTouchMix-30SoftwareControl App: 3.0.22Firmware: 3.0.12462ProblemTouchMix-30 Pro shows ‘Unknown Device’ in the Device List under Remote Control Settings.CausesThis...
View ArticleFAQ | What is the GXD amplifier input to output latency?
AnswerThe input to output latency of the GXD series amplifiers is 100us or 100 microseconds. This is fixed, regardless of processing used, unless delay is applied.
View ArticleFAQ | What is the main difference between legacy K and K.2 Series?
AnswerThere are many differences:K.2 amp has over twice the Peak power of legacy K with more efficient distribution of power (1800 W for the LF + 225W for the HF).K.2 has more powerful DSP, and now...
View ArticleFAQ | What are the Dante®/Network EtherCON ports for on the LA108/LA112?
AnswerThe dual EtherCON ports can be connected to a local area network (LAN), over which remote control and monitoring of the loudspeaker(s) is available via the local area network using the QSC...
View ArticleFAQ | What is the paint specification for KW Series speakers?
AnswerUse these specifications for paint touch-ups:Binder Type: Water-acrylicGloss Level: Half MattColor: Graphite Black (RAL 9011)
View ArticleTip | KS212C Cardioid Subwoofer Application Guide.
AdviceThe KS212C Cardioid Subwoofer Application Guide contains a wealth of information in regards to design configuration, system setup, and typical applications for optimal deployment of the KS212C.
View ArticleFAQ | Can the RJ45 connector on the Touchmix 30 be used with digital snake?
AnswerNo. The RJ45 connection on the mixer is for a router for wireless control of the unit only.
View ArticleFAQ | How does the KS212C differ from the KSub?
AnswerThe KSub is a single chamber 4th Order Bandpass system that is optimized for compactness and portability. In order to achieve cardioid coverage, the KS212C Cardioid Sub requires a somewhat larger...
View ArticleFAQ | Is the LS118 flyable?
AnswerThe LS118 has fittings that accommodate M10 Eyebolts. Flying an array consisting of multiple subwoofers is not supported. Always be sure to observe safe rigging practices and local regulations...
View ArticleTip | Setting up an Extreme Networks Summit X450-G2 Series network switch.
AdviceThe Network Switch Setup Guide for the Summit X450-G2 series contains step by step instructions for utilizing Q-SYS with this network switch.
View ArticleHow To | Connect TouchMix to an existing network in a facility.
ProcedureIf the network has been set up by IT professionals, they may be reluctant to allow it. But if they do, they will want to know two things.What port do you want them to give you?Answer – any...
View ArticleFAQ | What is the maximum Delay time you can set on the K.2 series of...
AnswerThe maximum Delay time is 100mS, which equates to approximately 112.6ft (34.6m).
View ArticleFAQ | Can I power an additional passive loudspeaker off my K.2/KW/KLA/CP...
AnswerThe question often comes up among users of K.2, KW, KLA, and CP Series active loudspeakers: How can I run a passive loudspeaker off my active loudspeaker?The answer is you cannot; each QSC active...
View ArticleFAQ | Can I mix-and-match up my legacy K and KW Series loudspeakers with...
AnswerAs long as they are separated by a short distance then yes, it will be fine. For example if you are using the new K.2 loudspeakers for your mains and KW or legacy K’s for your monitors, then this...
View ArticleFAQ | Is the K OUTDOOR COVER compatible with both legacy K and K.2 series?
AnswerYes. They can be used interchangeably.
View Article